• icon-wishlist
  • icon-cart
Voir tous les produits COBRA

Cheville en plastique TripleGrip(MC) # 12, 1 5/8'', pqt/8

Article #0484422 Modèle #173R Format #12
Cet article n'est pas offert pour le moment, mais il peut être commandé en visitant le magasin sélectionné. Les magasins reçoivent généralement les produits dans un délai de 3 à 7 jours à partir de la date de la commande.

Cheville en plastique TripleGrip(MC) # 12, 1 5/8'', pqt/8

icon-wishlist

Description

La cheville TripleGrip (TM) de Cobra est facile à installer et est conçue avec deux ailes extensibles qui adhèrent fermement derrière la cloison sèche pour une puissance de maintien maximale. Sa technologie avancée d'action de came s'élargit, créant ainsi une pression supplémentaire contre les parois latérales de la cloison sèche ou de la maçonnerie. Deux ailes latérales maintiennent l'ancrage en place en empêchant toute rotation pendant que la vis est insérée. La trousse comprend 8 chevilles # 12, 8 vis et 1 mèche 5/16''.

Caractéristiques

Modèle
TripleGrip
Composante
Plastique
Couleur
Vert
Longueur
1 5/8'' (4,13 cm)
Quantité par boite
8 chevilles, 8 vis, 1 mèche

Vous pourriez aussi aimer

Cheville en plastique, 1 1/4'', bte/75, bleu icon-wishlist
COBRA
Cheville en plastique, 1 1/4'', bte/75, bleu
Format 1 1/4"xBT75
Détails
Article #0484173
Ancrages et vis autoforeurs «Walldriller», #8, 4 PK icon-wishlist
COBRA
Ancrages et vis autoforeurs «Walldriller», #8, 4 PK
Format #8xPK4
Détails
Article #0484471
Chevilles avec vis icon-wishlist
COBRA
Chevilles avec vis
Format 1"xPK/30
Détails
Article #0484213
Ancrages et vis autoforeurs «Walldriller», #6, 12 PK icon-wishlist
COBRA
Ancrages et vis autoforeurs «Walldriller», #6, 12 PK
Format #6xPK12
Détails
Article #0484472
Chevilles avec vis icon-wishlist
COBRA
Chevilles avec vis
Format #8-10x1 1/4"
Détails
Article #0484214
Cheville en plastique TripleGrip(TM) # 10, 1 5/8'', pqt/4 icon-wishlist
COBRA
Cheville en plastique TripleGrip(TM) # 10, 1 5/8'', pqt/4
Format #10xPK4
Détails
Article #0484426
Ancrages avec vis « WallDriller », icon-wishlist
COBRA
Ancrages avec vis « WallDriller »,
Format #8xPK10
Détails
Article #0484473
Ancrages et vis autoforeurs «Walldriller», #8, 4 PK icon-wishlist
COBRA
Ancrages et vis autoforeurs «Walldriller», #8, 4 PK
Format #8xPK4
Détails
Article #0484476
Ancrages et vis autoforeurs «Walldriller», #6, 200 PK icon-wishlist
COBRA
Ancrages et vis autoforeurs «Walldriller», #6, 200 PK
Format #6xPK200
Détails
Article #0484479
Ancrage «DrillerToggle» pour mur creux, 3/16" x 2", 6/pqt icon-wishlist
COBRA
Ancrage «DrillerToggle» pour mur creux, 3/16" x 2", 6/pqt
Format 3/16"x2"xPK/6
Détails
Article #0484401
Ancrage «DrillerToggle» pour mur creux, 1/8" x 2", 6/pqt icon-wishlist
COBRA
Ancrage «DrillerToggle» pour mur creux, 1/8" x 2", 6/pqt
Format 1/8"x2"xPK/6
Détails
Article #0484397
Ancrage «FlipToggle» avec boulons, 1/4" x 2 1/2", 10/pqt icon-wishlist
FLIP TOGGLE
Ancrage «FlipToggle» avec boulons, 1/4" x 2 1/2", 10/pqt
Format 1/4"x2.5"xPK10
Détails
Article #04845651
Cheville en plastique TripleGrip(TM) # 10, 1 5/8'', pqt/50 icon-wishlist
COBRA
Cheville en plastique TripleGrip(TM) # 10, 1 5/8'', pqt/50
Format #10xPK50
Détails
Article #0484427
Ancrages avec vis « WallDriller » icon-wishlist
COBRA
Ancrages avec vis « WallDriller »
Format #8LxBT/40
Détails
Article #0484209
Cheville en plastique TripleGrip(TM) # 12, 1 5/8'', pqt/40 icon-wishlist
COBRA
Cheville en plastique TripleGrip(TM) # 12, 1 5/8'', pqt/40
Format #12
Détails
Article #0484424
Ancrages et vis autoforeurs «Walldriller», #6, 12 PK icon-wishlist
COBRA
Ancrages et vis autoforeurs «Walldriller», #6, 12 PK
Format #6xPK12
Détails
Article #0484477
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • LOCAL, getContent, 0ms
  • QUESTIONS, PRODUCT
  • bvseo-msg: The resource to the URL or file is currently unavailable.;
Cheville en plastique TripleGrip(MC) # 12, 1 5/8'', pqt/8 est évalué 4.2 de 5 de 37.
Rated 5 de 5 de par I needed a solution to protect my queen palms in pots along a back wall. Heavy winds were blowing some over and breaking expensive pots. So by using these anchors with heavy eyelets I was able to fashion restraints using heavy green twine to create restraints to keep them from swaying. It all worked perfectly. One installation tip.....after drilling the hole for your anchor..put one of the included screws in the anchor and seat it a few turns then tap it in with a hammer. This will allow for easier installation without collapsing the anchor and help seat it flush in the wall.
Date de publication: 2014-04-04
Rated 4 de 5 de par Good quality fastener, Could be better The included stucco bit is an excellent idea. It is the right size. The plastic expansion anchors could be a better quality to tap into place with a hammer into the stucco. I had to use an extra anchor , because of the bad twist as I tapped it into place. The screws are excellent with a large Phillips head screwdriver. I personally wouldn't use a flat head screw driver.
Date de publication: 2014-08-05
Rated 1 de 5 de par Completely Useless I tried installing these 3 times into drywall, and each time they failed. I got the screw halfway through, but then the anchor would just spin in place and not tighten any more. At that point, with the anchor partially opened inside the wall, removing them involved a pair of pliers and created big fat holes in the wall. Caused more damage than they're worth... A total waste of time and money.
Date de publication: 2014-02-09
Rated 1 de 5 de par A waste of money These anchors attempt to replicate the advantages of molly and toggle bolts, but they fall short. When I drilled the screws into the set anchors to my desired depth, the anchors would not grip the drywall and essentially stripped the pilot holes in the drywall. I had to remove the anchors and use traditional metal toggle bolts (after another run to the store). Spend a little more and use the real (metal) molly or toggle bolts.
Date de publication: 2017-08-29
Rated 5 de 5 de par Best never fail install I have used these many times and find that it is much easier to install in the hole if you will insert the provided screw as far as possible by hand into the plastic element and then tap it gently into the hole. Then remove the screw and attach what you plan to. The screw holds the plastic element rigid so that it does not collapse when forced into the hole. Try it... [This review was collected as part of a promotion.]
Date de publication: 2018-11-05
Rated 3 de 5 de par Some Reservations Used these on a rough exterior stucco wall. Hole size is critical. Just drilling hole with supplied drill was slightly too small and pounding too hard on insert will mangle it. I had to wiggle drill around just a little bit to enlarge hole slightly so that insert fit snugly in hole with slight hammer tap. If hole too large, insert will spin preventing screw from tightening. If done properly, anchor will hold well.
Date de publication: 2018-02-19
Rated 1 de 5 de par Garbage in concrete I used the included bit to drill a hole in ceramic tile with concrete backing. After successfully drilling one hole, I tried to insert the grip into the hole but it would not go because the expansion part expanded before going into the hole. I tried 4 grips and they all failed. The hole was at least 1" longer than the grip so it wasn't bottoming out. Junk!
Date de publication: 2017-05-23
Rated 5 de 5 de par Worked well where nothing but mollies would have We found these anchors to provide a solid hold. Even with a few removals and replacements, we only wasted one. These anchors work on sheet rock in a way that the twist in anchors don't, and I love them. This is our second purchase to make sure we have some on hand. The trick is to partially insert the anchor then add the screw and push it all in
Date de publication: 2016-04-19
  • y_2020, m_2, d_17, h_12
  • bvseo_bulk, prod_bvrr, vn_bulk_3.0.5
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_37
  • loc_fr_CA, sid_0484422, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_rona
  • bvseo_sdk, java_sdk, bvseo-4.0.0
  • LOCAL, getContent, 2ms
  • REVIEWS, PRODUCT