Product selection from
SHARKBITE
Description
This Sharkbite(TM) ball valve is the easiest way to install a new or replacement shut-off ball valve. It connects copper, CPVC and PEX pipe, without soldering, clamps, unions or glue. It is certified to 200 PSI and 93°C.,CSA Listed.
Product specifications
Size
3/4'' (1.9 cm)
Degree
93°C
Component
Brass
Capacity
200 PSI
Model
Push-to-connect
Standards
CSA Listed
You may also like
Sharkbite Shut-Off Ball Valve - Brass - 200-PSI Capacity - 3/4-in Dia Inlet - CSA Listed is rated
out of
5 by
7.
Rated 2 out of
5
by
Wendy E from
Not that easy
These are not as easy as they say. Maybe it would have helped if there were some detailed instructions in the package. Even the internet instructions were not that great. You need a 'disconnect clip' to complete the installation and that is not mentioned. Also, I had to install this shut off valve on already installed pipe, which had no give at all. Very difficult. If it weren't for the help and physical strength of my daughter, I would still be fighting it. Took 3 hours and 2 ball valves since one got broken in the process. Once we got it in, all was good but.... not a walk in the park by any means.
Date published: 2018-05-26
Rated 1 out of
5
by
Meneedhelp from
Why is it leaking
Last summer I installed a 3/4 ball valve to my outside water. It worked fine. This year I opened it back up and water is squirting out.
What happened
Date published: 2016-06-26
Rated 3 out of
5
by
John De from
Not use in closed up walls
Good valve as long as it installed outside a wall. Bought this one as a shut off for an outside faucet supply line. The stem however is too short and needs to be approx 2" to 3" longer for it to be inside a wall to have access to the stem & lever attachment. Tried to locate a stem extension of 1" to 3" but none are available for sharkbite. Ended up re-installing my outside faucet without an inside shut off valve and hope it last without freezing any further.
Date published: 2023-01-11
Rated 5 out of
5
by
cmtst from
End the frustration
After a week of trying to repair an out of service plastic shut-off valve, my local hardware told me about the SharkBite. My old plastic supply lines were smaller than the standard replacement fittings. That frustrating week of trying to stop a leak around that old size pipe using hoarded old fittings, compression, first the purple stuff, then the glue, now tape...now putty...self made washer, o-rings almost drove me to insanity. When my rep told me that the SharkBite would adjust to my ID/OD with one push, guaranteed, it sounded too good to be true. IT WAS THAT EASY. Cutting off the section I'd been working on was the hardest part. The SharkBite simply pushed on and no leak. I was amazed and could not have been happier!!! It worked, it really, really worked with one push. No tape, no putty, no leak!!! Homeowner repairs made simple!!! I'm sure my local professional plumbers don't want me to talk about this, but I'm telling all the neighbors who have the outdated supply lines. Thank you for this product!!!
Date published: 2017-01-31
Rated 5 out of
5
by
Susan613 from
QUICK, EASY, JOB DONE !!
[This review was collected as part of a promotion.] City is changing all water meters. Because of the 1 foot clearance it was harder to cut out and remove the old shut off tap, but install the ball valve 1 minute !! Always keep a few on hand for the unexpected leak!!
Date published: 2017-07-27
Rated 5 out of
5
by
JMHall from
swap out old pipe for new
Part of the copper pipe coming from my water heater corroded through. I used SharkBite connections for my new pipe installation. Easy Peasy! This product is so easy to work with and performs perfectly.
Date published: 2019-01-11
Rated 1 out of
5
by
Stephen from
HARD to remove!
Bad product did NOT stop the water flow, just reduced the flow in the off position. And
Date published: 2016-07-18
Helpful Links
Customer Services
About RONA
